Imported Vacuum Pumps · Repair · Parts · Systems
register Cart exit
Vacuum solutions, engineered for you ZEDAZK · Imported Vacuum Pumps, Repair & Parts
GLOBAL SALES Request a quote Reply within 24 hours

contact us

ZVDVAC
Address: Chashan Town, Dongguan City
Contact: Mr. Liu (Sales Manager)

frequently asked question

FAQ · Frequently asked

Selection, operation and maintenance — answered

Collected from real enquiries and service visits. If your question is not here, send us your process details and we will answer directly.

Define the process first

Start with four points: target working pressure, required pumping speed, gas composition and temperature, and daily running hours. Rotary vane pumps suit medium vacuum and general industrial duty; Roots pumps are normally used as boosters in combination with a backing pump; dry screw and oil-free pumps fit clean processes or gas streams with particles and moisture.

Send us your process data and our engineers will match a pump against its real pumping-speed curve, not just the catalogue maximum.

Oil-lubricated pumps use oil for sealing, lubrication and cooling. They reach lower ultimate pressure and cost less to buy, but need regular oil changes and protection against oil backstreaming. Oil-free pumps avoid oil contamination and need less maintenance, which suits food, medical and electronics applications, although ultimate pressure and efficiency are usually lower than an equivalent oil-lubricated pump.

Choose oil-lubricated rotary vane pumps when a trace of oil vapour is acceptable and lower pressure matters; choose oil-free or dry pumps when cleanliness is a hard requirement.

Pumping speed is the volume of gas removed per unit time (m³/h or L/s) and determines how fast the chamber is evacuated. Ultimate pressure is the lowest pressure the pump can reach (mbar or Pa) and determines the final vacuum level. The two must be read together: near ultimate pressure, actual pumping speed drops sharply.

Select against the speed at your working pressure and allow margin for piping, valves and filters. A common rule is to size for 1.2–1.5 times the required speed.

For normal duty, inspect oil level and condition, inlet filter, belt tension and seals every 3–6 months. Dusty, humid or corrosive service should be checked every 1–3 months. Stop and inspect immediately if noise increases, speed drops, oil emulsifies or the pump overheats.

Condition-based records — oil temperature, running hours and vacuum level — reveal degradation earlier than a fixed calendar interval.

Change mineral oil at about 2,000–4,000 running hours or every six months, whichever comes first. Synthetic oil can last longer. Humid, dusty or high-temperature duty needs shorter intervals and oil-circuit flushing.

Replace the oil filter at the same time, check the inlet strainer and exhaust filter, and never mix oils of different brands or grades.

Work from the outside in:

  • Leaks in piping, flanges or valves — perform a pressure-rise test first
  • Blocked inlet filter or exhaust filter
  • Emulsified or degraded oil, or low oil level
  • Worn seals, rotor or vanes
  • Gas too hot, too humid or heavily loaded with dust
  • Gas ballast or check valve not working correctly

Most low-vacuum complaints trace back to leaks or oil condition — check those before stripping the pump.

Yes, with the right configuration: gas ballast, a pre-condenser or moisture trap, corrosion-resistant materials and the correct oil, plus shorter oil-change intervals. For heavy moisture, strong corrosives or particles, an oil-free, dry screw or liquid-ring solution is usually safer.

Tell us the gas composition, temperature and moisture level and we will design the risk out at the selection stage.

Send the brand, model, serial number or a photo of the part. We stock vanes, filter elements, bearings, seals and repair kits for BECKER, Leybold, BUSCH, Rietschle, Edwards and Atlas Copco pumps, with genuine or high-quality alternative parts depending on lead time and budget.

For consumables, we recommend keeping an annual usage stock to avoid downtime waiting for parts.

Provide the process flow diagram, target vacuum and pumping speed, gas composition and temperature, number of simultaneous stations, pipe length and elevation, plus site power and installation space.

We then complete pump selection, piping calculations, receiver and filter sizing, controls and alarms, and deliver an equipment list with quotation.

Send the model, fault description and a photo or short video. We will diagnose remotely first and advise on the next step. If an on-site visit is needed, an engineer is scheduled by region.

Spare parts and repair service cover the Pearl River Delta and major industrial areas across China, for both in-warranty and out-of-warranty equipment.

Still have a question?Send your process, gas composition and target vacuum — we will recommend a pump and quote.
Request a quote
X Dongguan Zeda Vacuum Equipment Co., Ltd. Official Website

Scan the QR code with WeChat

WeChat ID: zedazk

(Click the ID to copy and add us)

Open WeChat

WeChat has been copied. Please open WeChat to add consultation details!
Quote WhatsApp Email Us Call Us WeChat Back to Top